Louver Instructions-
1. Make sure the white dots on louver connecting panel face the translucent front of soff box.
2. Aluminum pins on each louver panel are attached into pre-formed flutes marked with white dots.
3. Louvers face away from translucent front of soff box.
4. Insert first louver into both panels. Insert each following louver ina similar fashion, connecting both panels to louver before proceeding to the next louver.
5. After louvers are assembled, with louvers facing outward, bend panel flaps down and place connecting panels onto velcro sewn into feathered edge of soff box.
6. When finished louvers should be facing outward, white dots on louver panels should be facing translucent front of soff box.

Instructions for Starfish
1. Attach STARFISH centering bracket ("L" shaped) to your Starfish backplate. You will note a shoulder thumbscrew is attached to a support base in one of the six sections of your Starfish backplate. This is what your centering bracket mounts to using the shoulder thumbscrew.
2. Make sure the centering bracket is placed so it is on the inside of your Starfish backplate, or your strobe head and fabric flaps will not attach!
3. Open Starfish until front (translucent fabric) is taunt, then tighten thumb screw.
4. Insert Starfish handle (shaft) into backplate centering bracket; let it drop-don't tighten thumbscrew.
5. Pull five panels only back to backplate and attach Grommets to backplate corner pins. Two Grommets overlap each other at corner pins.
6. The sixth panel is left open so you can reach in, push shaft on centering bracket until side flaps, (black and silver) are taunt. Tighten thumbscrew and attach sixth panel.
7. Attach your strobe head light to a light stand and connect your Starfish to it. Some prefer the reverse: connect your strobe head to your Starfish first, then attach to a light stand.

Although the STARFISH collapsible design is like that of an umbrella, it should not be opened and closed exactly like one. Open and close the STARFISH in the upside-down position. Make sure the back flaps are tucked underneath the ribs. When folding the STARFISH for storage, let all flaps fall out and roll it up.

Instructions for Soff Strip RS
1. Place fabric on flat surface with silver side up.
2. Position strobe connector backplate face down. inserting each of the four corner hub pins into the four Grommet holes in the fabric. Be sure the backplate is positioned correctly so that when the rods are inserted into the corner hubs, they will be going in the right direction.
3. Insert ONE rod at a time into the corner hubs, and pull the corresponding grommeted fabric up and over the rod tip pin. REMEMBER! Assemble only one rod into corner hub and fabric attachment at a time. NOTE: Some of the Soff Strip RS rods have bends in them. Make sure they are inserted into the corner hub so that the rod extends to an upward position. (channel side of the rod always faces fabric).
4. Pull the grommeted fabric, one corner at a time, up and over the rod tip pin. Your Soff Strip RS will form its shape. IMPORTANT! Sometimes a grommet will slip off a back plate corner hub pin, this will cause your fabric to "hang-up" making it difficult to pull the fabric to the rod tip. Double check these points during assembly.
5. Inside baffle: If you wish to use it, attach to corresponding velcro.
6. Attach your strobe head to a light stand and connect your Soff Strip RS to it. Some prefer the reverse: connect your strobe head to your Soff Strip RS first, then attach to a light stand.
NOTE: If your SOFF STRIP is "lopsided" it is because one or more of the rods are not fully inserted (seated) into the corner hubs.

Soff Box RS Instructions
1. Place fabric on flat surface with silver side up.
2. Position strobe connector (spin ring backplate) face down, so that your connector will be outside your Soff Box RS.
3. Insert each of the four backplate pins into the four grommet holes in the fabric.
4. Insert one rod at a time into the corner hubs, and pull the corresponding grommeted fabric up and over to the rod pin. REMEMBER! Assemble only one rod into corner hub and fabric attachment at a time. NOTE: some of the Soff Box RS rods have bends in them. Make sure they are inserted into the corner hub so that the rod extends to an upward position. (channel side of the rod always faces up)
5. IMPORTANT! Sometimes a grommet will slip off a backplate corner hub pin, this will cause your fabric to "hang-up" making it difficult to pull the fabric to the rod tip. DOUBLE check these points during assembly.
6. Inside baffle: if you wish to use it, attach to corresponding velcro.
7. Attach your strobe head to a light stand and connect your Soff Box RS to it. Some prefer the reverse: connect your strobe head to your Soff Box RS first, then to a light stand.
NOTE: if your Soff Box is "lopsided" it is because one or more of the rods are not fully inserted (seated) into the corner hubs.

To open the reflectasol hold it upside down by the center rod. Grasp the ribs firmly between your fingers and palms and exert pressure to completely compress the spring. Bend the center arm slightly , stand reflectasol upright and adjust center rod to the position desired.

1. The windbrace is shaped like a "T" at the bottom of the T is a hole with a thumbscrew, put the center rod of your reflector in the hole (make sure the thumbscrew is unscrewed to allow the center rod to slide in).

2. The top of the "T" haS two u shaped notches. Slide the windbrace up the center rod until the top of the "T" has reached the X of the main frame of the reflector. Slide the top of the "T" into place until it holds firmly.

3. Tighten down the thumbscrew and your reflector is ready.

1. The windbrace is shaped like a "T" at the bottom of the T is a hole with a thumbscrew, put the center rod of your reflector in the hole (make sure the thumbscrew is unscrewed to allow the center rod to slide in).

2. The top of the "T" has two u shaped notches. Slide the windbrace up the center rod until the top of the "T" has reached the X of the main frame of the reflector. Slide the top of the "T" into place until it holds firmly.

3. Tighten down the thumbscrew and your reflector is ready.

Large Boom Arm Instruction Sheet
1.Take the three casters out of package. When taking out caster spacers will be included.

2.Open the 13’ HD stand. At the end of each leg is a hole. Line up the nipple on the spacers, with the hole.

3. On the caster unscrew the knob. At the end of the leg on the stand, slide the caster over the spacer, tighten the knob: do the same on all three casters.

4. Mounting bracket: There are two knobs with the mounting bracket. On the back of the bracket there are two tabs that say PULL, pull off tabs and screw the two knobs to the bracket. With the two knobs in place, put mounting bracket on top of your 13’ HD stand, tighten knob to the stand.

5. locate the silver “top” to the stand”: This “top” attaches to your light. Take”the top” slide into the end of the pole, with the knob attached, tighten down knob.

6. There are 2 boom arm parts: Take the two parts and line them up. Line up the hex screw on one end of the pole with the holes. After the two ends are together, use the allen key to tighten down the hex screw.

7. On the stand, loosen the top knob on mounting bracket. Slide the pole into the boom arm mounting bracket. Slide the arm about half way down the mounting bracket, tighten knob on the mounting bracket.


8. Last is the counterweight, the parts included are:
1 knob, 1 black washer, 1 black backing plate &1 spring. Take the black washer and slide it on the knob, place the backing plate on, then the spring . Tighten knob snug, but not all the way, on the top of the counterweight.

9. Now slide on counterweight tighten knob.

NOTE: Before placing any SOFFBOX or LIGHTS on stand MAKE SURE ALL KNOBS ARE TIGHTEN DOWN!!!!!!